Akbari-Ganji Homotopy Perturbation Method for Analyzing the Pulsatile Blood Flow in Tapered Stenosis Arteries under the Effect of Magnetic Field together with the Impact of Mass and Heat Transfer

Document Type : Research Paper

Authors

Department of Mathematics, College of Education for Pure Science, Basrah University, Basrah, Iraq

Abstract

The two-dimensional pulsatile blood flow in tapered stenosis arteries under the effect of a Magnetic field with mass and heat transfer was analyzed by using a new analytical method called the Akbari-Ganji homotopy perturbation method (AGHPM).This technique is based on integrating the Akbari-Ganji and the homotopy perturbation methods. We succeeded in developing the mathematical model studied by researchers Liu and Liu by adding the effect of the magnetic field of blood flow in addition to the effect of mass and heat transfer on it, this developed model has not been studied before. In the two states (absence and presence) of a magnetic field; the axial velocity, the wall shear stress, flow resistance and volumetric flow rate were investigated under the impact of the angle of tapering, the Grashof number, the solutal Grashof number and magnetic field. The results show that in the case of the absence magnetic field there is good agreement with the previous study made by the researchers Liu and Liu, while in the case of the presence magnetic field it is noted that when the magnetic field increases from 2 to 6, the velocity and flow rate decrease, but in contrast the wall shear stress and resistance flow increases. Moreover, the results establish that AGHPM is effective and extremely accurate in determining the analytical approximate solution for pulsatile blood flow in tapered stenosis arteries under magnetic field influence. Furthermore, the graphs of this novel solution demonstrate the validity, usefulness, and substantiality of AGHPM, and are consistent with the results of earlier investigations.

Keywords

Main Subjects

[1]          N. Ali, A. Zaman, M. Sajid, Unsteady blood flow through a tapered stenotic artery using Sisko model, Computers & Fluids, Vol. 101, pp. 42-49, 2014.
[2]          S. Chakravarty, P. Mandal, A nonlinear two-dimensional model of blood flow in an overlapping arterial stenosis subjected to body acceleration, Mathematical and computer modelling, Vol. 24, No. 1, pp. 43-58, 1996.
[3]          S. Changdar, S. De, Analysis of non-linear pulsatile blood flow in artery through a generalized multiple stenosis, Arabian Journal of Mathematics, Vol. 5, No. 1, pp. 51-61, 2016.
[4]          P. K. Mandal, S. Chakravarty, A. Mandal, N. Amin, Effect of body acceleration on unsteady pulsatile flow of non-Newtonian fluid through a stenosed artery, Applied Mathematics and Computation, Vol. 189, No. 1, pp. 766-779, 2007.
[5]          V. Srivastava, R. Rastogi, R. Vishnoi, A two-layered suspension blood flow through an overlapping stenosis, Computers & Mathematics with Applications, Vol. 60, No. 3, pp. 432-441, 2010.
[6]          A. Zaman, N. Ali, M. Sajid, T. Hayat, Effects of unsteadiness and non-Newtonian rheology on blood flow through a tapered time-variant stenotic artery, AIP advances, Vol. 5, No. 3, pp. 037129, 2015.
[7]          M. S. Dada, F. Alamu-Awoniran, Heat and Mass Transfer in Micropolar Model for Blood Flow Through a Stenotic Tapered Artery, Applications and Applied Mathematics: An International Journal (AAM), Vol. 15, No. 2, pp. 24, 2020.
[8]          G. Shit, S. Majee, Pulsatile flow of blood and heat transfer with variable viscosity under magnetic and vibration environment, Journal of Magnetism and Magnetic Materials, Vol. 388, pp. 106-115, 2015.
[9]          S. Shaw, P. Murthy, S. Pradhan, The effect of body acceleration on two dimensional flow of Casson fluid through an artery with asymmetric stenosis, The Open Conservation Biology Journal, Vol. 2, No. 1, 2010.
[10]        M. Sharma, R. Gaur, INTERNATIONAL JOURNAL OF ENGINEERING SCIENCES & RESEARCH TECHNOLOGY MODELING OF MHD BLOOD FLOW IN A BALLOON CATHETERIZED ARTERIAL STENOSIS WITH THERMAL RADIATION.
[11]        R. Ponalagusamy, S. Priyadharshini, A numerical model on pulsatile flow of magnetic nanoparticles as drug carrier suspended in Herschel–Bulkley fluid through an arterial stenosis under external magnetic field and body force, International Journal of Computer Mathematics, Vol. 96, No. 9, pp. 1763-1786, 2019.
[12]        B. Tripathi, B. Sharma, Effect of variable viscosity on MHD inclined arterial blood flow with chemical reaction, International Journal of Applied Mechanics and Engineering, Vol. 23, No. 3, 2018.
[13]        R. Ellahi, S. Rahman, S. Nadeem, Blood flow of Jeffrey fluid in a catherized tapered artery with the suspension of nanoparticles, Physics Letters A, Vol. 378, No. 40, pp. 2973-2980, 2014.
[14]        M. Danesh, A. Farajpour, M. Mohammadi, Axial vibration analysis of a tapered nanorod based on nonlocal elasticity theory and differential quadrature method, Mechanics Research Communications, Vol. 39, No. 1, pp. 23-27, 2012.
[15]        S. Faghiri, S. Akbari, M. B. Shafii, K. Hosseinzadeh, Hydrothermal analysis of non-Newtonian fluid flow (blood) through the circular tube under prescribed non-uniform wall heat flux, Theoretical and Applied Mechanics Letters, Vol. 12, No. 4, pp. 100360, 2022.
[16]        K. Hosseinzadeh, S. Salehi, M. Mardani, F. Mahmoudi, M. Waqas, D. Ganji, Investigation of nano-Bioconvective fluid motile microorganism and nanoparticle flow by considering MHD and thermal radiation, Informatics in Medicine Unlocked, Vol. 21, pp. 100462, 2020.
[17]        M. Mohammadi, A. Farajpour, A. Moradi, M. Hosseini, Vibration analysis of the rotating multilayer piezoelectric Timoshenko nanobeam, Engineering Analysis with Boundary Elements, Vol. 145, pp. 117-131, 2022.
[18]        M. Mohammadi, A. Rastgoo, Primary and secondary resonance analysis of FG/lipid nanoplate with considering porosity distribution based on a nonlinear elastic medium, Mechanics of Advanced Materials and Structures, Vol. 27, No. 20, pp. 1709-1730, 2020.
[19]        M. Mohammadi, M. Hosseini, M. Shishesaz, A. Hadi, A. Rastgoo, Primary and secondary resonance analysis of porous functionally graded nanobeam resting on a nonlinear foundation subjected to mechanical and electrical loads, European Journal of Mechanics-A/Solids, Vol. 77, pp. 103793, 2019.
[20]        M. Mohammadi, A. Rastgoo, Nonlinear vibration analysis of the viscoelastic composite nanoplate with three directionally imperfect porous FG core, Structural Engineering and Mechanics, An Int'l Journal, Vol. 69, No. 2, pp. 131-143, 2019.
[21]        A. Farajpour, A. Rastgoo, M. Mohammadi, Vibration, buckling and smart control of microtubules using piezoelectric nanoshells under electric voltage in thermal environment, Physica B: Condensed Matter, Vol. 509, pp. 100-114, 2017.
[22]        A. Farajpour, M. H. Yazdi, A. Rastgoo, M. Loghmani, M. Mohammadi, Nonlocal nonlinear plate model for large amplitude vibration of magneto-electro-elastic nanoplates, Composite Structures, Vol. 140, pp. 323-336, 2016.
[23]        A. Farajpour, M. Yazdi, A. Rastgoo, M. Mohammadi, A higher-order nonlocal strain gradient plate model for buckling of orthotropic nanoplates in thermal environment, Acta Mechanica, Vol. 227, No. 7, pp. 1849-1867, 2016.
[24]        M. Mohammadi, M. Safarabadi, A. Rastgoo, A. Farajpour, Hygro-mechanical vibration analysis of a rotating viscoelastic nanobeam embedded in a visco-Pasternak elastic medium and in a nonlinear thermal environment, Acta Mechanica, Vol. 227, No. 8, pp. 2207-2232, 2016.
[25]        M. R. Farajpour, A. Rastgoo, A. Farajpour, M. Mohammadi, Vibration of piezoelectric nanofilm-based electromechanical sensors via higher-order non-local strain gradient theory, Micro & Nano Letters, Vol. 11, No. 6, pp. 302-307, 2016.
[26]        M. Baghani, M. Mohammadi, A. Farajpour, Dynamic and stability analysis of the rotating nanobeam in a nonuniform magnetic field considering the surface energy, International Journal of Applied Mechanics, Vol. 8, No. 04, pp. 1650048, 2016.
[27]        M. Goodarzi, M. Mohammadi, M. Khooran, F. Saadi, Thermo-mechanical vibration analysis of FG circular and annular nanoplate based on the visco-pasternak foundation, Journal of Solid Mechanics, Vol. 8, No. 4, pp. 788-805, 2016.
[28]        H. Asemi, S. Asemi, A. Farajpour, M. Mohammadi, Nanoscale mass detection based on vibrating piezoelectric ultrathin films under thermo-electro-mechanical loads, Physica E: Low-dimensional Systems and Nanostructures, Vol. 68, pp. 112-122, 2015.
[29]        M. Safarabadi, M. Mohammadi, A. Farajpour, M. Goodarzi, Effect of surface energy on the vibration analysis of rotating nanobeam, 2015.
[30]        M. Goodarzi, M. Mohammadi, A. Gharib, Techno-Economic Analysis of Solar Energy for Cathodic Protection of Oil and Gas Buried Pipelines in Southwestern of Iran, in Proceeding of, https://publications.waset.org/abstracts/33008/techno-economic-analysis-of …, pp.
[31]        M. Mohammadi, A. A. Nekounam, M. Amiri, The vibration analysis of the composite natural gas pipelines in the nonlinear thermal and humidity environment, in Proceeding of, https://civilica.com/doc/540946/, pp.
[32]        M. Goodarzi, M. Mohammadi, M. Rezaee, Technical Feasibility Analysis of PV Water Pumping System in Khuzestan Province-Iran, in Proceeding of, https://publications.waset.org/abstracts/18930/technical-feasibility …, pp.
[33]        M. Mohammadi, A. Farajpour, A. Moradi, M. Ghayour, Shear buckling of orthotropic rectangular graphene sheet embedded in an elastic medium in thermal environment, Composites Part B: Engineering, Vol. 56, pp. 629-637, 2014.
[34]        M. Mohammadi, A. Moradi, M. Ghayour, A. Farajpour, Exact solution for thermo-mechanical vibration of orthotropic mono-layer graphene sheet embedded in an elastic medium, Latin American Journal of Solids and Structures, Vol. 11, pp. 437-458, 2014.
[35]        M. Mohammadi, A. Farajpour, M. Goodarzi, F. Dinari, Thermo-mechanical vibration analysis of annular and circular graphene sheet embedded in an elastic medium, Latin American Journal of Solids and Structures, Vol. 11, pp. 659-682, 2014.
[36]        M. Mohammadi, A. Farajpour, M. Goodarzi, Numerical study of the effect of shear in-plane load on the vibration analysis of graphene sheet embedded in an elastic medium, Computational Materials Science, Vol. 82, pp. 510-520, 2014.
[37]        A. Farajpour, A. Rastgoo, M. Mohammadi, Surface effects on the mechanical characteristics of microtubule networks in living cells, Mechanics Research Communications, Vol. 57, pp. 18-26, 2014.
[38]        S. R. Asemi, M. Mohammadi, A. Farajpour, A study on the nonlinear stability of orthotropic single-layered graphene sheet based on nonlocal elasticity theory, Latin American Journal of Solids and Structures, Vol. 11, pp. 1541-1546, 2014.
[39]        M. Goodarzi, M. Mohammadi, A. Farajpour, M. Khooran, Investigation of the effect of pre-stressed on vibration frequency of rectangular nanoplate based on a visco-Pasternak foundation, 2014.
[40]        S. Asemi, A. Farajpour, H. Asemi, M. Mohammadi, Influence of initial stress on the vibration of double-piezoelectric-nanoplate systems with various boundary conditions using DQM, Physica E: Low-dimensional Systems and Nanostructures, Vol. 63, pp. 169-179, 2014.
[41]        S. Asemi, A. Farajpour, M. Mohammadi, Nonlinear vibration analysis of piezoelectric nanoelectromechanical resonators based on nonlocal elasticity theory, Composite Structures, Vol. 116, pp. 703-712, 2014.
[42]        M. Mohammadi, M. Ghayour, A. Farajpour, Free transverse vibration analysis of circular and annular graphene sheets with various boundary conditions using the nonlocal continuum plate model, Composites Part B: Engineering, Vol. 45, No. 1, pp. 32-42, 2013.
[43]        M. Mohammadi, M. Goodarzi, M. Ghayour, A. Farajpour, Influence of in-plane pre-load on the vibration frequency of circular graphene sheet via nonlocal continuum theory, Composites Part B: Engineering, Vol. 51, pp. 121-129, 2013.
[44]        M. Mohammadi, A. Farajpour, M. Goodarzi, R. Heydarshenas, Levy type solution for nonlocal thermo-mechanical vibration of orthotropic mono-layer graphene sheet embedded in an elastic medium, Journal of Solid Mechanics, Vol. 5, No. 2, pp. 116-132, 2013.
[45]        M. Mohammadi, A. Farajpour, M. Goodarzi, H. Mohammadi, Temperature Effect on Vibration Analysis of Annular Graphene Sheet Embedded on Visco-Pasternak Foundati, Journal of Solid Mechanics, Vol. 5, No. 3, pp. 305-323, 2013.
[46]        A. Farajpour, A. Shahidi, M. Mohammadi, M. Mahzoon, Buckling of orthotropic micro/nanoscale plates under linearly varying in-plane load via nonlocal continuum mechanics, Composite Structures, Vol. 94, No. 5, pp. 1605-1615, 2012.
[47]        M. Mohammadi, M. Goodarzi, M. Ghayour, S. Alivand, Small scale effect on the vibration of orthotropic plates embedded in an elastic medium and under biaxial in-plane pre-load via nonlocal elasticity theory, 2012.
[48]        A. Farajpour, M. Mohammadi, A. Shahidi, M. Mahzoon, Axisymmetric buckling of the circular graphene sheets with the nonlocal continuum plate model, Physica E: Low-dimensional Systems and Nanostructures, Vol. 43, No. 10, pp. 1820-1825, 2011.
[49]        A. Farajpour, M. Danesh, M. Mohammadi, Buckling analysis of variable thickness nanoplates using nonlocal continuum mechanics, Physica E: Low-dimensional Systems and Nanostructures, Vol. 44, No. 3, pp. 719-727, 2011.
[50]        H. Moosavi, M. Mohammadi, A. Farajpour, S. Shahidi, Vibration analysis of nanorings using nonlocal continuum mechanics and shear deformable ring theory, Physica E: Low-dimensional Systems and Nanostructures, Vol. 44, No. 1, pp. 135-140, 2011.
[51]        M. Mohammadi, M. Ghayour, A. Farajpour, Analysis of free vibration sector plate based on elastic medium by using new version differential quadrature method, Journal of solid mechanics in engineering, Vol. 3, No. 2, pp. 47-56, 2011.
[52]        A. Farajpour, M. Mohammadi, M. Ghayour, Shear buckling of rectangular nanoplates embedded in elastic medium based on nonlocal elasticity theory, in Proceeding of, www.civilica.com/Paper-ISME19-ISME19_390.html, pp. 390.
[53]        M. Mohammadi, A. Farajpour, A. R. Shahidi, Higher order shear deformation theory for the buckling of orthotropic rectangular nanoplates using nonlocal elasticity, in Proceeding of, www.civilica.com/Paper-ISME19-ISME19_391.html, pp. 391.
[54]        M. Mohammadi, A. Farajpour, A. R. Shahidi, Effects of boundary conditions on the buckling of single-layered graphene sheets based on nonlocal elasticity, in Proceeding of, www.civilica.com/Paper-ISME19-ISME19_382.html, pp. 382.
[55]        M. Mohammadi, M. Ghayour, A. Farajpour, Using of new version integral differential method to analysis of free vibration orthotropic sector plate based on elastic medium, in Proceeding of, www.civilica.com/Paper-ISME19-ISME19_497.html, pp. 497.
[56]        N. Ghayour, A. Sedaghat, M. Mohammadi, Wave propagation approach to fluid filled submerged visco-elastic finite cylindrical shells, 2011.
[57]        M. Mohammadi, A. Farajpour, A. Rastgoo, Coriolis effects on the thermo-mechanical vibration analysis of the rotating multilayer piezoelectric nanobeam, Acta Mechanica, https://doi.org/10.1007/s00707-022-03430-0, 2023.
[58]        X. Luo, Z. Kuang, A study on the constitutive equation of blood, Journal of biomechanics, Vol. 25, No. 8, pp. 929-934, 1992.
[59]        Y. Liu, W. Liu, Blood flow analysis in tapered stenosed arteries with the influence of heat and mass transfer, Journal of Applied Mathematics and Computing, Vol. 63, No. 1, pp. 523-541, 2020.
[60]        H. Aminikhah, M. Hemmatnezhad, An efficient method for quadratic Riccati differential equation, Communications in Nonlinear Science and Numerical Simulation, Vol. 15, No. 4, pp. 835-839, 2010.
[61]        M. A. Ikbal, S. Chakravarty, K. K. Wong, J. Mazumdar, P. K. Mandal, Unsteady response of non-Newtonian blood flow through a stenosed artery in magnetic field, Journal of Computational and Applied Mathematics, Vol. 230, No. 1, pp. 243-259, 2009.
[62]        G. Varshney, V. Katiyar, S. Kumar, Effect of magnetic field on the blood flow in artery having multiple stenosis: a numerical study, International Journal of Engineering, Science and Technology, Vol. 2, No. 2, pp. 967-82, 2010.
[63]        H. Mirgolbabaee, S. Ledari, D. Ganji, Semi-analytical investigation on micropolar fluid flow and heat transfer in a permeable channel using AGM, Journal of the Association of Arab Universities for Basic and Applied Sciences, Vol. 24, pp. 213-222, 2017.
[64]        M. Mirzazadeh, Z. Ayati, New homotopy perturbation method for system of Burgers equations, Alexandria Engineering Journal, Vol. 55, No. 2, pp. 1619-1624, 2016.
Volume 53, Issue 4
December 2022
Pages 543-570
  • Receive Date: 08 September 2022
  • Revise Date: 04 October 2022
  • Accept Date: 05 October 2022