A review on stress distribution, strength and failure of bolted composite joints
Document Type : Review Paper
Authors
Department of Mechanical engineering, Shahid Chamran University of Ahvaz, Ahvaz, Iran
Abstract
In this study, analytical models considering different material and geometry for both single and double-lap bolted joints were reviewed for better understand how to select the proper model for a particular application. The survey indicades that the analytic models selected for the adhesively single or double bolted lap joints, as well as T, scarf, and stepped joints, with linear material properties are mostly two dimensional and the studies on stress distribution and/or failure of the joint are performed either experimentally, analytically or by finite element method. The results seem to be generally accurate and adequate. Additionally, it was shown that any increase in the bolt-hole clearance leads to an increase in bolt rotation, as well as a decrease in bolt-hole contact area, and hence, a reduction in joint stiffness. Moreover, studies on hybrid joints have revealed that the proper choice of adhesive material in conjunction with bolts or rivets in a joint, allows for significant increase in the static and fatigue strength compared to similar pure bonded joints. Additionally, the results on hybrid scarf joints showed that it is vital to place fasteners closer to the ends of the overlap to suppress the peak peeling stresses and hence, delay the effects of early crack initiation in the adhesive layer...
Keywords
Main Subjects
[1] D. M. Gleich, Stress analysis of structural bonded joints, Delft University Press, 2002, pp. 122.
[2] M. Shishesaz, M. M. Attar, H. Robati, The Effect of Fiber Arrangement on Stress Concentration Around a Pin in a Laminated Composite Joint, in ASME, 10th Biennial Conference on Engineering Systems Design and Analysis ESDA2010-24587, 2010, pp. 153-161.
[3] S. Zhou, Z. Wang, J. Zhou, X. Wu, Experimental and numerical investigation on bolted composite joint made by vacuum assisted resin injection, Composites Part B: Engineering, Vol. 45, pp. 1620-1628, 2013.
[4] Load Development and Automation for Composite Bolted Joint Bearing and Bypass Analysis, 2010 (American Institute of Aeronautics and Astronautics).
[5] M. Keikhosravy, R. Hashemi Oskouei, P. Soltani, A. Atas, C. Soutis, Effect of geometric parameters on the stress distribution in Al 2024-T3 single-lap bolted joints, International Journal of Structural Integrity, Vol. 3, No. 1, pp. 79-93, 2012.
[6] W.-H. Chen, S.-S. Lee, J.-T. Yeh, Three-dimensional contact stress analysis of a composite laminate with bolted joint, Composite Structures, Vol. 30, pp. 287-297, 1995.
[7] T. J. Whitney, E. V. Iarve, R. A. Brockman, Singular stress fields near contact boundaries in a composite bolted joint, International Journal of Solids and Structures, Vol. 41, pp. 1893-1909, 2004.
[8] F. Ascione, A preliminary numerical and experimental investigation on the shear stress distribution on multi-row bolted FRP joints, Mechanics Research Communications, Vol. 37, No. 2, pp. 164-168, 2010/03/01/, 2010.
[9] M. H. Ahmad, Stress distribution in composite double-lap bolted joints incorporating with clamp-up, Applied Mechanics and Materials, Vol. 660, pp. 152-156, 2014.
[10] Analysis of a Preloaded Bolted Joint in a Ceramic Composite Combustor, 2003 (American Institute of Aeronautics and Astronautics).
[11] M. P. Cavatorta, D. S. Paolino, L. Peroni, M. Rodino, A finite element simulation and experimental validation of a composite bolted joint loaded in bending and torsion, Composites Part A: Applied Science and Manufacturing, Vol. 38, pp. 1251-1261, 2007.
[12] An experimental investigation of composite bonded and/or bolted repairs using single lap joint designs, 1997 (American Institute of Aeronautics and Astronautics).
[13] An Analytical Method for Evaluating Bolted Joint Repairs in Composite Structures, 2011 (American Institute of Aeronautics and Astronautics).
[14] A. Vander Klok, A. Dutta, S. A. Tekalur, Metal to composite bolted joint behavior evaluated at impact rates of loading, Composite Structures, Vol. 106, pp. 446-452, 2013.
[15] P. P. Camanho, C. M. L. Tavares, R. de Oliveira, A. T. Marques, A. J. M. Ferreira, Increasing the efficiency of composite single-shear lap joints using bonded inserts, Composites Part B: Engineering, Vol. 36, pp. 372-383, 2005.
[16] A. M. Girão Coelho, J. T. Mottram, A review of the behaviour and analysis of bolted connections and joints in pultruded fibre reinforced polymers, Materials & Design, Vol. 74, pp. 86-107, 2015/06/05/, 2015.
[17] C. T. McCarthy, P. J. Gray, An analytical model for the prediction of load distribution in highly torqued multi-bolt composite joints, Composite Structures, Vol. 93, No. 2, pp. 287-298, 2011/01/01/, 2011.
[18] K. Bodjona, K. Raju, G.-H. Lim, L. Lessard, Load sharing in single-lap bonded/bolted composite joints. Part I: Model development and validation, Composite Structures, Vol. 129, pp. 268-275, 2015.
[19] K. Bodjona, L. Lessard, Load sharing in single-lap bonded/bolted composite joints. Part II: Global sensitivity analysis, Composite Structures, Vol. 129, pp. 276-283, 2015.
[20] K. P. Raju, K. Bodjona, G.-H. Lim, L. Lessard, Improving load sharing in hybrid bonded/bolted composite joints using an interference-fit bolt, Composite Structures, Vol. 149, pp. 329-338, 2016.
[21] V. Mara, R. Haghani, M. Al-Emrani, Improving the performance of bolted joints in composite structures using metal inserts, Journal of Composite Materials, Vol. 50, No. 21, pp. 3001-3018, 2016.
[22] E. Paroissien, F. Lachaud, S. Schwartz, A. Da Veiga, P. Barrière, Simplified stress analysis of hybrid (bolted/bonded) joints, International Journal of Adhesion and Adhesives, Vol. 77, pp. 183-197, 2017/09/01/, 2017.
[23] F. Taheri-Behrooz, A. R. Shamaei Kashani, R. N. Hefzabad, Effects of material nonlinearity on load distribution in multi-bolt composite joints, Composite Structures, Vol. 125, pp. 195-201, 2015/07/01/, 2015.
[24] C. Santiuste, E. Barbero, M. Henar Miguélez, Computational analysis of temperature effect in composite bolted joints for aeronautical applications, Journal of Reinforced Plastics and Composites, Vol. 30, No. 1, pp. 3-11, 2011.
[25] A. Olmedo, C. Santiuste, E. Barbero, An analytical model for the secondary bending prediction in single-lap composite bolted-joints, Composite Structures, Vol. 111, pp. 354-361, 2014/05/01/, 2014.
[26] L. Awadhani, A. Bewoor, Behavior of single lap composite bolted joint under traction loading: Experimental investigation, in Proceeding of, AIP Publishing, pp. 020124.
[27] S. W. Wang, X. Q. Cheng, X. Guo, X. Li, G. Chen, Influence of Lateral Displacement of the Grip on Single lap Composite-to-Aluminum Bolted Joints, Experimental Mechanics, Vol. 56, No. 3, pp. 407-417, March 01, 2016.
[28] J. Kratochvil, W. Becker, Structural analysis of composite bolted joints using the complex potential method, Composite Structures, Vol. 92, No. 10, pp. 2512-2516, 2010/09/01/, 2010.
[29] Y. Zhou, Q. Fei, Evaluation of opening-hole shapes for rivet connection of a composite plate, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Vol. 231, No. 20, pp. 3810-3817, 2017.
[30] T. Qin, L. Zhao, J. Zhang, Fastener effects on mechanical behaviors of double-lap composite joints, Composite Structures, Vol. 100, pp. 413-423, 2013/06/01/, 2013.
[31] I. F. Soykok, End geometry and pin-hole effects on axially loaded adhesively bonded composite joints, Composites Part B: Engineering, Vol. 77, pp. 129-138, 2015/08/01/, 2015.
[32] G. M. Pearce, A. F. Johnson, R. S. Thomson, D. W. Kelly, Experimental Investigation of Dynamically Loaded Bolted Joints in Carbon Fibre Composite Structures, Applied Composite Materials, Vol. 17, No. 3, pp. 271-291, June 01, 2010.
[33] S. Daouk, F. Louf, C. Cluzel, O. Dorival, L. Champaney, S. Audebert, Study of the dynamic behavior of a bolted joint under heavy loadings, Journal of Sound and Vibration, Vol. 392, pp. 307-324, 2017/03/31/, 2017.
[34] G. M. K. Pearce, A. F. Johnson, A. K. Hellier, R. S. Thomson, A Stacked-Shell Finite Element Approach for Modelling a Dynamically Loaded Composite Bolted Joint Under in-Plane Bearing Loads, Applied Composite Materials, Vol. 20, No. 6, pp. 1025-1039, December 01, 2013.
[35] L. Feo, G. Marra, A. S. Mosallam, Stress analysis of multi-bolted joints for FRP pultruded composite structures, Composite Structures, Vol. 94, No. 12, pp. 3769-3780, 2012/12/01/, 2012.
[36] Z. Shen, D. Hu, Y. Zhang, Q. Cai, X. Han, Continuous twice-impacts analysis of UHMWPE laminate fixed with bolted joints, International Journal of Impact Engineering, Vol. 109, pp. 293-301, 2017/11/01/, 2017.
[37] M. Y. Tsai, J. Morton, An investigation into the stresses in double-lap adhesive joints with laminated composite adherends, International Journal of Solids and Structures, Vol. 47, pp. 3317-3325, 2010.
[38] M. Y. Tsai, J. Morton, F. L. Matthews, Experimental and Numerical Studies of a Laminated Composite Single-Lap Adhesive Joint, Journal of Composite Materials, Vol. 29, pp. 1254-1275, 1995.
[39] Q. M. Li, R. A. W. Mines, R. S. Birch, Static and dynamic behaviour of composite riveted joints in tension, International Journal of Mechanical Sciences, Vol. 43, pp. 1591-1610, 2001.
[40] S. W. Lee, D. G. Lee, K. S. Jeong, Static and Dynamic Torque Characteristics of Composite Cocured Single Lap Joint, Journal of Composite Materials, Vol. 31, pp. 2188-2201, 1997.
[41] C. Stocchi, P. Robinson, S. T. Pinho, A detailed finite element investigation of composite bolted joints with countersunk fasteners, Composites Part A: Applied Science and Manufacturing, Vol. 52, pp. 143-150, 2013/09/01/, 2013.
[42] B. Mandal, A. Chakrabarti, A simple homogenization scheme for 3D finite element analysis of composite bolted joints, Composite Structures, Vol. 120, pp. 1-9, 2015/02/01/, 2015.
[43] H.-T. Thai, B. Uy, Finite element modelling of blind bolted composite joints, Journal of Constructional Steel Research, Vol. 112, pp. 339-353, 2015/09/01/, 2015.
[44] N. M. Chowdhury, W. K. Chiu, J. Wang, P. Chang, Experimental and finite element studies of bolted, bonded and hybrid step lap joints of thick carbon fibre/epoxy panels used in aircraft structures, Composites Part B: Engineering, Vol. 100, pp. 68-77, 2016/09/01/, 2016.
[45] L. Prabhu, V. Krishnaraj, S. Sathish, V. Sathyamoorthy, Experimental and Finite Element Analysis of GFRP Composite Laminates with Combined Bolted and Bonded Joints, Indian Journal of Science and Technology, Vol. 10, No. 14, 2017.
[46] P. J. Gray, C. T. McCarthy, A highly efficient user-defined finite element for load distribution analysis of large-scale bolted composite structures, Composites Science and Technology, Vol. 71, No. 12, pp. 1517-1527, 2011/08/19/, 2011.
[47] P. J. Gray, C. T. McCarthy, A global bolted joint model for finite element analysis of load distributions in multi-bolt composite joints, Composites Part B: Engineering, Vol. 41, pp. 317-325, 2010.
[48] L. Zhou, D. Zhang, L. Zhao, X. Zhou, J. Zhang, F. Liu, Design and analysis of a novel bolted composite π joint under bending load, Materials & Design, Vol. 98, pp. 201-208, 2016/05/15/, 2016.
[49] X. Cheng, J. Fan, S. Liu, X. Guo, Y. Xu, T. Zhang, Design and investigation of composite bolted π-joints with an unconventional configuration under bending load, Composites Part B: Engineering, Vol. 85, pp. 59-67, 2016/02/01/, 2016.
[50] P. Lopez-Cruz, J. Laliberté, L. Lessard, Investigation of bolted/bonded composite joint behaviour using design of experiments, Composite Structures, Vol. 170, pp. 192-201, 2017/06/15/, 2017.
[51] A. Vassilopoulos, 2014, Fatigue and fracture of adhesively-bonded composite joints, Elsevier,
[52] T. Ireman, Three-dimensional stress analysis of bolted single-lap composite joints, Composite Structures, Vol. 43, No. 3, pp. 195-216, 1998/11/01/, 1998.
[53] K. I. Tserpes, G. Labeas, P. Papanikos, T. Kermanidis, Strength prediction of bolted joints in graphite/epoxy composite laminates, Composites Part B: Engineering, Vol. 33, No. 7, pp. 521-529, 2002/10/01/, 2002.
[54] Y. Xiao, T. Ishikawa, Bearing strength and failure behavior of bolted composite joints (part I: Experimental investigation), Composites Science and Technology, Vol. 65, No. 7, pp. 1022-1031, 2005/06/01/, 2005.
[55] Y. Xiao, T. Ishikawa, Bearing strength and failure behavior of bolted composite joints (part II: modeling and simulation), Composites Science and Technology, Vol. 65, No. 7, pp. 1032-1043, 2005/06/01/, 2005.
[56] P. A. Sharos, B. Egan, C. T. McCarthy, An analytical model for strength prediction in multi-bolt composite joints at various loading rates, Composite Structures, Vol. 116, pp. 300-310, 2014/09/01/, 2014.
[57] M. A. McCarthy, C. T. McCarthy, V. P. Lawlor, W. F. Stanley, Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: part I—model development and validation, Composite Structures, Vol. 71, pp. 140-158, 2005.
[58] C. T. McCarthy, M. A. McCarthy, Three-dimensional finite element analysis of single-bolt, single-lap composite bolted joints: Part II––effects of bolt-hole clearance, Composite Structures, Vol. 71, pp. 159-175, 2005.
[59] P. J. Gray, C. T. McCarthy, An analytical model for the prediction of through-thickness stiffness in tension-loaded composite bolted joints, Composite Structures, Vol. 94, No. 8, pp. 2450-2459, 2012/07/01/, 2012.
[60] M. El Zaroug, F. Kadioglu, M. Demiral, D. Saad, Experimental and numerical investigation into strength of bolted, bonded and hybrid single lap joints: Effects of adherend material type and thickness, International Journal of Adhesion and Adhesives, Vol. 87, pp. 130-141, 2018/12/01/, 2018.
[61] L. Zhao, M. Shan, F. Liu, J. Zhang, A probabilistic model for strength analysis of composite double-lap single-bolt joints, Composite Structures, Vol. 161, pp. 419-427, 2017/02/01/, 2017.
[62] H.-L. Ma, Z. Jia, K.-t. Lau, X. Li, D. Hui, S.-q. Shi, Enhancement on mechanical strength of adhesively-bonded composite lap joints at cryogenic environment using coiled carbon nanotubes, Composites Part B: Engineering, Vol. 110, pp. 396-401, 2017/02/01/, 2017.
[63] A. Othman, K. J. Jadee, M.-Z. Ismadi, Mitigating stress concentration through defense hole system for improvement in bearing strength of composite bolted joint, Part 1: Numerical analysis, Journal of Composite Materials, Vol. 51, No. 26, pp. 3685-3699, 2017.
[64] H. Li, Z. Lu, Y. Zhang, Probabilistic strength analysis of bolted joints in laminated composites using point estimate method, Composite Structures, Vol. 88, No. 2, pp. 202-211, 2009/04/01/, 2009.
[65] J. H. Choi, Y. H. Lee, J. H. Kweon, W. S. Che, Strength of Composite Laminated Bolted Joint Subjected to a Clamping Force, Key Engineering Materials, Trans Tech Publ, 2006, pp. 1777-1780.
[66] H.-S. Chen, The static and fatigue strength of bolted joints in composites with hygrothermal cycling, Composite Structures, Vol. 52, No. 3, pp. 295-306, 2001/05/01/, 2001.
[67] Y. Ling, An estimation method of bearing strength of bolted joints in fibre reinforced composite, Applied Mathematics and Mechanics, Vol. 7, No. 1, pp. 103-109, January 01, 1986.
[68] Y. Pekbey, The bearing strength and failure behavior of bolted e-glass/epoxy composite joints, Mechanics of Composite Materials, Vol. 44, No. 4, pp. 397-414, July 01, 2008.
[69] T. Katsumata, Y. Mizutani, A. Todoroki, R. Matsuzaki, Study of high-strength CFRP bolted joints with failure-monitoring cone washers, Frontiers of Mechanical Engineering, Vol. 6, No. 3, pp. 272, August 20, 2011.
[70] T. Collings, 1977, The strength of bolted joints in multi-directional CFRP laminates, Citeseer,
[71] G. Kretsis, F. L. Matthews, The strength of bolted joints in glass fibre/epoxy laminates, Composites, Vol. 16, No. 2, pp. 92-102, 1985/04/01/, 1985.
[72] H. Ahmad, A. D. Crocombe, P. A. Smith, Strength prediction in CFRP woven laminate bolted double-lap joints under quasi-static loading using XFEM, Composites Part A Applied Science and Manufacturing, Vol. 56, pp. 192–202, 2014.
[73] A. Ataş, C. Soutis, Strength prediction of bolted joints in CFRP composite laminates using cohesive zone elements, Composites Part B: Engineering, Vol. 58, pp. 25-34, 2014.
[74] F. Esmaeili, M. Zehsaz, T. N. Chakherlou, Experimental Investigations on the Effects of Torque Tightening on the Fatigue Strength of Double-lap Simple Bolted and Hybrid (Bolted/Bonded) Joints, Strain, Vol. 50, No. 4, pp. 347-354, 2014.
[75] O. Sayman, R. Siyahkoc, F. Sen, R. Ozcan, Experimental Determination of Bearing Strength in Fiber Reinforced Laminated Composite Bolted Joints under Preload, Journal of Reinforced Plastics and Composites, Vol. 26, No. 10, pp. 1051-1063, 2007.
[76] P. D. Herrington, M. Sabbaghian, Effect of Radial Clearance between Bolt and Washer on the Bearing Strength of Composite Bolted Joints, Journal of Composite Materials, Vol. 26, No. 12, pp. 1826-1843, 1992.
[77] F. Esmaeili, M. Zehsaz, T. N. Chakherlou, S. Hasanifard, Experimental and Numerical Study of the Fatigue Strength of Double Lap Bolted Joints and the Effect of Torque Tightening on the Fatigue Life of Jointed Plates, Transactions of the Indian Institute of Metals, Vol. 67, No. 4, pp. 581-588, August 01, 2014.
[78] H. Ahmad, A. D. Crocombe, P. A. Smith, Strength prediction in CFRP woven laminate bolted single-lap joints under quasi-static loading using XFEM, Composites Part A: Applied Science and Manufacturing, Vol. 66, pp. 82-93, 2014/11/01/, 2014.
[79] L. Liu, J. Zhang, K. Chen, H. Wang, Influences of assembly parameters on the strength of bolted composite-metal joints under tensile loading, Advanced Composite Materials, Vol. 22, No. 5, pp. 339-359, 2013/10/01, 2013.
[80] J. H. Walter, R. R. Schmitt, Influence of Clamp-Up Force on the Strength of Bolted Composite Joints, AIAA Journal, Vol. 32, No. 3, pp. 665-667, 1994/03/01, 1994.
[81] F. X. Irisarri, F. Laurin, N. Carrere, 6 - Strength prediction of bolted joints in carbon fibre reinforced polymer (CFRP) composites, in: P. Camanho, L. Tong, Composite Joints and Connections, Eds., pp. 208-244: Woodhead Publishing, 2011.
[82] S. Nilsson, Increasing Strength of Graphite/Epoxy Bolted Joints by Introducing an Adhesively Bonded Metallic Insert, Journal of Composite Materials, Vol. 23, No. 7, pp. 642-650, 1989.
[83] F. Gamdani, R. Boukhili, A. Vadean, Tensile strength of open-hole, pin-loaded and multi-bolted single-lap joints in woven composite plates, Materials & Design, Vol. 88, pp. 702-712, 2015/12/25/, 2015.
[84] H. Ahmad, M. A. Abed, Strength Prediction of Double-Lap Bolted Joints of Woven Fabric CFRP Composite Plates Using Hashin Formulations, in Proceeding of, Trans Tech Publ, pp. 290-294.
[85] F. Nerilli, G. Vairo, Progressive damage in composite bolted joints via a computational micromechanical approach, Composites Part B: Engineering, Vol. 111, pp. 357-371, 2017/02/15/, 2017.
[86] H. Yazdani Nezhad, B. Egan, F. Merwick, C. T. McCarthy, Bearing damage characteristics of fibre-reinforced countersunk composite bolted joints subjected to quasi-static shear loading, Composite Structures, Vol. 166, pp. 184-192, 2017/04/15/, 2017.
[87] B. He, D. Ge, Coupled continuum damage mechanics and failure envelope method for failure prediction of composite multi-bolt joints, Journal of Reinforced Plastics and Composites, Vol. 36, No. 8, pp. 563-578, 2017.
[88] Y. Zhou, H. Yazdani Nezhad, C. Hou, X. Wan, C. T. McCarthy, M. A. McCarthy, A three dimensional implicit finite element damage model and its application to single-lap multi-bolt composite joints with variable clearance, Composite Structures, Vol. 131, pp. 1060-1072, 2015/11/01/, 2015.
[89] A. Du, Y. Liu, H. Xin, Y. Zuo, Progressive damage analysis of PFRP double-lap bolted joints using explicit finite element method, Composite Structures, Vol. 152, pp. 860-869, 2016/09/15/, 2016.
[90] C. Hühne, A. K. Zerbst, G. Kuhlmann, C. Steenbock, R. Rolfes, Progressive damage analysis of composite bolted joints with liquid shim layers using constant and continuous degradation models, Composite Structures, Vol. 92, No. 2, pp. 189-200, 2010/01/01/, 2010.
[91] J. Zhang, F. Liu, L. Zhao, Y. Chen, B. Fei, A progressive damage analysis based characteristic length method for multi-bolt composite joints, Composite Structures, Vol. 108, pp. 915-923, 2014/02/01/, 2014.
[92] G. Kolks, K. I. Tserpes, Efficient progressive damage modeling of hybrid composite/titanium bolted joints, Composites Part A: Applied Science and Manufacturing, Vol. 56, pp. 51-63, 2014/01/01/, 2014.
[93] M. Chishti, C. H. Wang, R. S. Thomson, A. C. Orifici, Experimental investigation of damage progression and strength of countersunk composite joints, Composite Structures, Vol. 94, No. 3, pp. 865-873, 2012/02/01/, 2012.
[94] Y. Zhou, H. Yazdani-Nezhad, M. A. McCarthy, X. Wan, C. McCarthy, A study of intra-laminar damage in double-lap, multi-bolt, composite joints with variable clearance using continuum damage mechanics, Composite Structures, Vol. 116, pp. 441-452, 2014/09/01/, 2014.
[95] G. Lampeas, N. Perogamvros, Analysis of composite bolted joints by a macro-modelling approach, International Journal of Structural Integrity, Vol. 7, No. 3, pp. 412-428, 2016.
[96] A. Ataş, C. Soutis, Subcritical damage mechanisms of bolted joints in CFRP composite laminates, Composites Part B: Engineering, Vol. 54, pp. 20-27, 2013/11/01/, 2013.
[97] L. V. Awadhani, A. K. Bewoor, Analytical and experimental investigation of Effect of geometric parameters on the failure modes in a single lap single bolted metal to GFRP composite bolted joints subjected to axial tensile loading, Materials Today: Proceedings, Vol. 4, No. 8, pp. 7345-7350, 2017/01/01/, 2017.
[98] X. F. Hu, A. Haris, M. Ridha, V. B. C. Tan, T. E. Tay, Progressive failure of bolted single-lap joints of woven fibre-reinforced composites, Composite Structures, Vol. 189, pp. 443-454, 2018/04/01/, 2018.
[99] X. Cheng, S. Wang, J. Zhang, W. Huang, Y. Cheng, J. Zhang, Effect of damage on failure mode of multi-bolt composite joints using failure envelope method, Composite Structures, Vol. 160, pp. 8-15, 2017/01/15/, 2017.
[100] K. C. Warren, R. A. Lopez-Anido, S. S. Vel, H. H. Bayraktar, Progressive failure analysis of three-dimensional woven carbon composites in single-bolt, double-shear bearing, Composites Part B: Engineering, Vol. 84, pp. 266-276, 2016/01/01/, 2016.
[101] Z. Kapidžić, H. Ansell, J. Schön, K. Simonsson, Quasi-static bearing failure of CFRP composite in biaxially loaded bolted joints, Composite Structures, Vol. 125, pp. 60-71, 2015/07/01/, 2015.
[102] P. Liu, X. Cheng, S. Wang, S. Liu, Y. Cheng, Numerical analysis of bearing failure in countersunk composite joints using 3D explicit simulation method, Composite Structures, Vol. 138, pp. 30-39, 2016/03/15/, 2016.
[103] F. Nerilli, M. Marino, G. Vairo, A Numerical Failure Analysis of Multi-bolted Joints in FRP Laminates Based on Basalt Fibers, Procedia Engineering, Vol. 109, pp. 492-506, 2015/01/01/, 2015.
[104] M. Ozen, O. Sayman, Failure loads of mechanical fastened pinned and bolted composite joints with two serial holes, Composites Part B: Engineering, Vol. 42, No. 2, pp. 264-274, 2011/03/01/, 2011.
[105] U. A. Khashaba, T. A. Sebaey, K. A. Alnefaie, Failure and reliability analysis of pinned-joints composite laminates: Effects of stacking sequences, Composites Part B: Engineering, Vol. 45, No. 1, pp. 1694-1703, 2013/02/01/, 2013.
[106] U. Khashaba, T. Sebaey, K. Alnefaie, Failure and reliability analysis of pinned-joint composite laminates: Effects of pin–hole clearance, Journal of Composite Materials, Vol. 47, No. 18, pp. 2287-2298, 2013.
[107] Z. Wang, S. Zhou, J. Zhang, X. Wu, L. Zhou, Progressive failure analysis of bolted single-lap composite joint based on extended finite element method, Materials & Design, Vol. 37, pp. 582-588, 2012.
[108] F. Liu, L. Zhao, S. Mehmood, J. Zhang, B. Fei, A modified failure envelope method for failure prediction of multi-bolt composite joints, Composites Science and Technology, Vol. 83, pp. 54-63, 2013/06/28/, 2013.
[109] I. F. Soykok, O. Sayman, M. Ozen, B. Korkmaz, Failure analysis of mechanically fastened glass fiber/epoxy composite joints under thermal effects, Composites Part B: Engineering, Vol. 45, No. 1, pp. 192-199, 2013/02/01/, 2013.
[110] A. Ataş, G. F. Mohamed, C. Soutis, Progressive failure analysis of bolted joints in composite laminates, Plastics, Rubber and Composites, Vol. 41, No. 4-5, pp. 209-214, 2012/06/01, 2012.
[111] F. Lu, D. a. Cai, J. Tang, W. Li, J. Deng, G. Zhou, Bearing failure of single-/double-shear composite bolted joints: An explicit finite element modeling, Journal of Reinforced Plastics and Composites, Vol. 37, No. 14, pp. 933-944, 2018.
[112] S. Y. Lee, H. Ahmad, Bearing Stress at Failure of Double-Lap Hybrid Joints in Woven Fabric Kenaf Fiber Composite Plates under Quasi-static Loading, MATEC Web Conf., Vol. 103, pp. 02008, 2017.
[113] L. Zhao, T. Qin, J. Zhang, M. Shan, B. Fei, Determination method of stress concentration relief factors for failure prediction of composite multi-bolt joints, Journal of Composite Materials, Vol. 49, No. 14, pp. 1667-1680, 2015.
[114] J. Zhang, F. Liu, L. Zhao, J. Zhi, L. Zhou, B. Fei, Influence of end distances on the failure of composite bolted joints, Journal of Reinforced Plastics and Composites, Vol. 34, No. 5, pp. 388-404, 2015.
[115] Á. Olmedo, C. Santiuste, On the prediction of bolted single-lap composite joints, Composite Structures, Vol. 94, No. 6, pp. 2110-2117, 2012/05/01/, 2012.
[116] J. Fan, X. Cheng, S. Wang, X. Guo, T. Zhang, Experimental and numerical investigation of composite bolted π-joint subjected to bending load, Composites Part B: Engineering, Vol. 78, pp. 324-330, 2015/09/01/, 2015.
[117] M.-G. Ko, J.-H. Kweon, J.-H. Choi, Fatigue characteristics of jagged pin-reinforced composite single-lap joints in hygrothermal environments, Composite Structures, Vol. 119, pp. 59-66, 2015/01/01/, 2015.
[118] I. K. Giannopoulos, D. Doroni-Dawes, K. I. Kourousis, M. Yasaee, Effects of bolt torque tightening on the strength and fatigue life of airframe FRP laminate bolted joints, Composites Part B: Engineering, Vol. 125, pp. 19-26, 2017/09/15/, 2017.
[119] Y. Sun, G. Z. Voyiadjis, W. Hu, F. Shen, Q. Meng, Fatigue and fretting fatigue life prediction of double-lap bolted joints using continuum damage mechanics-based approach, International Journal of Damage Mechanics, Vol. 26, No. 1, pp. 162-188, 2017.
[120] G. Scarselli, E. Castorini, F. W. Panella, R. Nobile, A. Maffezzoli, Structural behaviour modelling of bolted joints in composite laminates subjected to cyclic loading, Aerospace Science and Technology, Vol. 43, pp. 89-95, 2015/06/01/, 2015.
[121] S. Zhou, Y. Sun, J. Ge, X. Chen, Multiaxial fatigue life prediction of composite bolted joint under constant amplitude cycle loading, Composites Part B: Engineering, Vol. 74, pp. 131-137, 2015/06/01/, 2015.
[122] Z. Kapidžić, H. Ansell, J. Schön, K. Simonsson, Fatigue bearing failure of CFRP composite in biaxially loaded bolted joints at elevated temperature, Composite Structures, Vol. 127, pp. 298-307, 2015/09/01/, 2015.
[123] J. Wang, N. Zhang, S. Guo, Experimental and numerical analysis of blind bolted moment joints to CFTST columns, Thin-Walled Structures, Vol. 109, pp. 185-201, 2016/12/01/, 2016.
[124] S. Heimbs, S. Schmeer, J. Blaurock, S. Steeger, Static and dynamic failure behaviour of bolted joints in carbon fibre composites, Composites Part A: Applied Science and Manufacturing, Vol. 47, pp. 91-101, 2013/04/01/, 2013.
[125] J. Zhang, F. Liu, L. Zhao, B. Fei, A novel characteristic curve for failure prediction of multi-bolt composite joints, Composite Structures, Vol. 108, pp. 129-136, 2014/02/01/, 2014.
[126] G. M. K. Pearce, A. F. Johnson, A. K. Hellier, R. S. Thomson, A study of dynamic pull-through failure of composite bolted joints using the stacked-shell finite element approach, Composite Structures, Vol. 118, pp. 86-93, 2014/12/01/, 2014.
[127] A. Fontanelli, P. Diaz Montiel, S. Venkataraman, Bearing Failure Predictions of Composite Bolted Joints using Continuum Damage Models, AIAA SciTech Forum in: 2018 AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, Eds.: American Institute of Aeronautics and Astronautics, 2018.
[128] F. Sen, M. Pakdil, O. Sayman, S. Benli, Experimental Failure Analysis of Glass-Epoxy Laminated Composite Bolted-Joints with Clearance Under Preload, International Journal of Damage Mechanics, Vol. 20, No. 2, pp. 163-178, 2011.
[129] W. J. Paulson, C. Oskay, Failure Prediction of Countersunk Composite Bolted Joints Using Reduced Order Multiple Space-Time Homogenization, in Proceeding of.
[130] A. P. K. Joseph, P. Davidson, A. M. Waas, Intra-inter Crack Band Model (I2CBM) for Progressive Damage and Failure Analysis of Joints, AIAA SciTech Forum in: 58th AIAA/ASCE/AHS/ASC Structures, Structural Dynamics, and Materials Conference, Eds.: American Institute of Aeronautics and Astronautics, 2017.
[131] B. Mandal, A. Chakrabarti, Numerical failure assessment of multi-bolt FRP composite joints with varying sizes and preloads of bolts, Composite Structures, Vol. 187, pp. 169-178, 2018/03/01/, 2018.
[132] J. B. Bai, R. A. Shenoi, X. Y. Yun, J. J. Xiong, Progressive damage modelling of hybrid RTM-made composite Π-joint under four-point flexure using mixed failure criteria, Composite Structures, Vol. 159, pp. 327-334, 2017/01/01/, 2017.
[133] J. H. Stockdale, F. L. Matthews, The effect of clamping pressure on bolt bearing loads in glass fibre-reinforced plastics, Composites, Vol. 7, No. 1, pp. 34-38, 1976/01/01/, 1976.
[134] T. Sawa, T. Kobayashi, The Strength of Joints Combining an Adhesive with a Bolt, The Journal of Adhesion, Vol. 25, No. 4, pp. 269-280, 1988/06/01, 1988.
[135] L. Yao, Q. Feng, D. Wan, L. Wu, K. Yang, J. Hou, B. Liu, Q. Wan, Experiment and finite element simulation of high strength steel adhesive joint reinforced by rivet for automotive applications, Journal of Adhesion Science and Technology, Vol. 31, No. 14, pp. 1617-1625, 2017/07/18, 2017.
[136] M. Y. Solmaz, T. Topkaya, Progressive Failure Analysis in Adhesively, Riveted, and Hybrid Bonded Double-Lap Joints, The Journal of Adhesion, Vol. 89, No. 11, pp. 822-836, 2013/11/02, 2013.
[137] G. Marannano, B. Zuccarello, Static strength and fatigue life of optimized hybrid single lap aluminum–CFRP structural joints, The Journal of Adhesion, Vol. 94, No. 7, pp. 501-528, 2018/06/07, 2018.
[138] G. Qin, J. Na, W. Tan, W. Mu, J. Ji, Failure prediction of adhesively bonded CFRP-Aluminum alloy joints using cohesive zone model with consideration of temperature effect, The Journal of Adhesion, pp. 1-24, 2018.
[139] T. Tannert, H. Zhu, S. Myslicki, F. Walther, T. Vallée, Tensile and fatigue investigations of timber joints with glued-in FRP rods, The Journal of Adhesion, Vol. 93, No. 11, pp. 926-942, 2017/09/19, 2017.
[140] A. M. Pereira, P. N. B. Reis, J. A. M. Ferreira, Effect of the mean stress on the fatigue behaviour of single lap joints, The Journal of Adhesion, Vol. 93, No. 6, pp. 504-513, 2017/05/12, 2017.
[141] S. O. Olajide, E. Kandare, A. A. Khatibi, Fatigue life uncertainty of adhesively bonded composite scarf joints – an airworthiness perspective, The Journal of Adhesion, Vol. 93, No. 7, pp. 515-530, 2017/06/07, 2017.
[142] T. Vallée, T. Tannert, S. Fecht, Adhesively bonded connections in the context of timber engineering – A Review, The Journal of Adhesion, Vol. 93, No. 4, pp. 257-287, 2017/03/21, 2017.
[143] E. W. Godwin, F. L. Matthews, A review of the strength of joints in fibre-reinforced plastics: Part 1. Mechanically fastened joints, Composites, Vol. 11, pp. 155-160, 1980.
[144] B. L. Agarwal, Static Strength Prediction of Bolted Joint in Composite Material, AIAA Journal, Vol. 18, pp. 1371-1375, 1980.
[145] W.-H. Lin, M.-H. R. Jen, The Strength of Bolted and Bonded Single-Lapped Composite Joints in Tension, Journal of Composite Materials, Vol. 33, pp. 640-666, 1999.
[146] P. A. Smith, K. J. Pascoe, C. Polak, D. O. Stroud, The behaviour of single-lap bolted joints in CFRP laminates, Composite Structures, Vol. 6, pp. 41-55, 1986.
[147] T. N. Chakherlou, M. J. Razavi, A. B. Aghdam, B. Abazadeh, An experimental investigation of the bolt clamping force and friction effect on the fatigue behavior of aluminum alloy 2024-T3 double shear lap joint, Materials & Design, Vol. 32, pp. 4641-4649, 2011.
[148] F. Esmaeili, M. Zehsaz, T. N. Chakherlou, Investigation the effect of tightening torque on the fatigue strength of double lap simple bolted and hybrid (bolted–bonded) joints using volumetric method, Materials & Design, Vol. 63, pp. 349-359, 2014.
[149] J. M. Mínguez, J. Vogwell, Effect of torque tightening on the fatigue strength of bolted joints, Engineering Failure Analysis, Vol. 13, pp. 1410-1421, 2006.
[150] D. S. Saunders, S. C. Galea, G. K. Deirmendjian, The development of fatigue damage around fastener holes in thick graphite/epoxy composite laminates, Composites, Vol. 24, pp. 309-321, 1993.
[151] B. Benchekchou, R. G. White, Stresses around fasteners in composite structures in flexure and effects on fatigue damage initiation part 1: cheese-head bolts, Composite Structures, Vol. 33, pp. 95-108, 1995.
[152] B. Benchekchou, R. G. White, Stresses around fasteners in composite structures in flexure and effects on fatigue damage initiation part 2: countersunk bolts, Composite Structures, Vol. 33, pp. 109-119, 1995.
[153] E. Persson, I. Eriksson, P. Hammersberg, Propagation of Hole Machining Defects in Pin-Loaded Composite Laminates, Journal of Composite Materials, Vol. 31, pp. 383-408, 1997.
[154] E. Persson, I. Eriksson, L. Zackrisson, Effects of hole machining defects on strength and fatigue life of composite laminates, Composites Part A: Applied Science and Manufacturing, Vol. 28, pp. 141-151, 1997.
[155] W. Li, H. Cai, C. Li, K. Wang, L. Fang, Micro-mechanics of failure for fatigue strength prediction of bolted joint structures of carbon fiber reinforced polymer composite, Composite Structures, Vol. 124, pp. 345-356, 2015.
[156] Experimental investigation of fatigue behaviour in composite bolted joints, 1999.
[157] A. Lanciotti, L. Lazzeri, M. Raggi, Fatigue behaviour of mechanically fastened joints in composite materials, Composite Structures, Vol. 33, pp. 87-94, 1995.
[158] R. Starikov, J. Schön, Local fatigue behaviour of CFRP bolted joints, Composites Science and Technology, Vol. 62, pp. 243-253, 2002.
[159] R. Starikov, Fatigue behaviour of mechanically fastened aluminium joints tested in spectrum loading, International Journal of Fatigue, Vol. 26, pp. 1115-1127, 2004.
[160] R. Starikov, J. Schön, Quasi-static behaviour of composite joints with protruding-head bolts, Composite Structures, Vol. 51, pp. 411-425, 2001.
[161] P. A. Smith, K. J. Pascoe, Fatigue of bolted joints in (0/90) CFRP laminates, Composites Science and Technology, Vol. 29, pp. 45-69, 1987.
[162] R. Starikov, J. Schön, Fatigue resistance of composite joints with countersunk composite and metal fasteners, International Journal of Fatigue, Vol. 24, pp. 39-47, 2002.
[163] R. Starikov, J. Schön, Experimental study on fatigue resistance of composite joints with protruding-head bolts, Composite Structures, Vol. 55, pp. 1-11, 2002.
[164] E. Persson, I. Eriksson, Fatigue of multiple-row bolted joints in carbon/epoxy laminates: ranking of factors affecting strength and fatigue life, International Journal of Fatigue, Vol. 21, pp. 337-353, 1999.
[165] A. M. Rubin, Common failure modes for composite aircraft structures due to secondary loads, Composites Engineering, Vol. 2, pp. 313-320, 1992.
[166] T. S. Lim, B. C. Kim, D. G. Lee, Fatigue characteristics of the bolted joints for unidirectional composite laminates, Composite Structures, Vol. 72, pp. 58-68, 2006.
[167] S. Seike, Y. Takao, W.-X. Wang, T. Matsubara, Bearing damage evolution of a pinned joint in CFRP laminates under repeated tensile loading, International Journal of Fatigue, Vol. 32, pp. 72-81, 2010.
[168] D. W. Wilson, Y. Tsujimoto, On phenomenological failure criteria for composite bolted joint analysis, Composites Science and Technology, Vol. 26, pp. 283-305, 1986.
[169] Z. Q. Wang, S. Zhou, J. F. Zhang, X. Q. Wang, Failure Load Prediction of Bolted Single-Lap Composite Joint Based on XFEM, Advanced Materials Research, Trans Tech Publ, 2011, pp. 742-745.
[170] S. Zhou, Z. Q. Wang, J. F. Zhang, Y. G. Xie, Influence of Ply Angle on Failure Response of Bolted Composite Joint, Advanced Materials Research, Trans Tech Publ, 2012, pp. 7128-7132.
[171] T. Sadowski, M. Kneć, P. Golewski, Experimental investigations and numerical modelling of steel adhesive joints reinforced by rivets, International Journal of Adhesion and Adhesives, Vol. 30, pp. 338-346, 2010.
[172] M. Grassi, B. Cox, X. Zhang, Simulation of pin-reinforced single-lap composite joints, Composites Science and Technology, Vol. 66, pp. 1623-1638, 2006.
[173] A. Ataş, C. Soutis, Application of cohesive zone elements in damage analysis of composites: Strength prediction of a single-bolted joint in CFRP laminates, International Journal of Non-Linear Mechanics, Vol. 66, pp. 96-104, 2014.
)
Volume 49, Issue 2
December 2018Pages 415-429
- Receive Date: 02 November 2018
- Revise Date: 30 November 2018
- Accept Date: 12 December 2018